61F-GPN2 AC from OMRON >> Specification: Liquid Level Controller, 61F- GP-N2 Series, Conductive, Vac, W, 80 ms. Find great deals for Omron 61F-GP-N2 Processor/Controller. Shop with confidence on eBay!. The 61F-GP-N2-AC is a Conductive Level Controller for automatic water supply and drainage control. Compact plug-in controller for single or two-point.

Author: Malazshura Tojind
Country: Barbados
Language: English (Spanish)
Genre: Music
Published (Last): 1 September 2009
Pages: 232
PDF File Size: 9.54 Mb
ePub File Size: 1.8 Mb
ISBN: 273-3-64557-347-7
Downloads: 72311
Price: Free* [*Free Regsitration Required]
Uploader: Mulkree

This is a temporal bone which had an implant electrode When draining, change the connection Tb to Ta.

Omron 61F-GP-N2 Processor/Controller | eBay

Easy-to-replace separate versions facilitate maintenance of electrodes. In the interest of product improvement, specifications are subject to change without notice. Between electrode E1 and E3 Release resistance Approx.

Limitation on Liability; Etc. Long distance for wiring may causes malfunctions because stray capacitance may influence operation, or abnormal surges or noise may run through electrode circuit s. Product specifications and accessories may be changed at any time based on improvements and other reasons. Doing so can reduce some effects of noise. Ideal for soft drink vendors, etc. Doing so may possibly result in electric shock. If this differential is not required, the low-level probe need not be connected.

However, some specifications of the Product may be changed without any notice. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments.

When using a noise filter, check the voltage and current and install it as close to the product as possible. In sewage use, electrode holders must be installed 10 to 20 cm apart from one another.


To convert grams into ounces, multiply by 0. The diagram shows the connections for water supply. Doing so causes malfunctions such as chattering, etc. Alarm control warning of abnormal or dangerously high or low levels.

In this case the relay does not de-energize until the water level falls below the low-level probe. Return of any 61r-gp-n2 by Buyer must be approved in writing by Omron before shipment.

All units are in millimeters unless otherwise indicated. For acids, alkalis and sea water, electrode holders may be as much as 1 meter apart to operate properly.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Iron is more reactive than copper. The earth terminal must be grounded. Buyer shall take application responsibility in all cases.

Using the low-level probe allows a wide 61f-yp-n2 between switching a pump on and off, and can avoid excessive pump operation during tank emptying or filling. After fixation, osmium staining, and dissection the Special 3-pole holder of small 61f-gp-2 and light weight.

61F-GP-N2 – OMRON Industrial Automation

Between electrode E2 and E3 Response time Operate: When in doubt, ojron part numbers may be assigned to fix or establish key specifications for your application. Indication of liquid buildup due to filter blockages. Connect the short electrode to E1, the medium electrode to E2, and the long electrode to E3.

Fully fit the electrode into the connecting nut attached to the electrode holder. When taping one of the electrodes to prevent it from contacting the other electrodes in water, do not tape the electrode entirely but leave at least mm of its end uncovered.


It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. Doing so causes malfunctions by getting vulnerable to induction noise.

Omron 61F-GP-N2 Processor/Controller

Omron disclaims all other warranties, express or implied. Electrochem review part 1 Consider the following two reactions: Use separator when connecting. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions.

When resistance to high pressure is required. A low voltage is applied between these probes and the earth probe or tank, if it is electrically conductive.

To convert millimeters into inches, multiply by 0. When the required length of the electrode is more than 1 m, use a separator at each joint of two electrodes so as to prevent the electrodes from contacting one another. For two-point control a low-level probe is used as well.

However, a type having 1, mm length electrodes is available on request. For low specific liquids. The water provides a current between the earth probe and the high-level probe. Spin a lock nut and ommron spring washer onto the electrode. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or 61v-gp-n2 to the above warranty. Precautions for Safe Use 1. If the sufficient interval cannot be provided, employ 61d-gp-n2 low-sensitivity type Floatless Level Controller.