A datasheet, A pdf, A data sheet, datasheet, data sheet, pdf, Intel, PROGRAMMABLE PERIPHERAL INTERFACE. INTEL (Programmable Peripheral Interface). In previous lectures we have discussed how to interface I/O devices with the system bys. If an input device. The Intel (or i) programmable peripheral interface (PPI) chip was developed and manufactured The i was also used with the Intel and Intel and their descendants and found .. “Intel 82c55 PPI Datasheet” (PDF ).

Author: Faezil Vokinos
Country: Colombia
Language: English (Spanish)
Genre: Travel
Published (Last): 9 June 2006
Pages: 36
PDF File Size: 6.33 Mb
ePub File Size: 3.3 Mb
ISBN: 440-4-62000-545-6
Downloads: 52220
Price: Free* [*Free Regsitration Required]
Uploader: Shajar

PPI interface for parallel port

Microprocessor And Its Applications. This means that data can be input or output on the same eight lines PA0 – PA7. The inputs are not ppk because the CPU only has to read their current values, then store the data in a CPU register or memory if it needs to be referenced at a later time.

As an example, consider an input device connected to at port A.

All of these chips were originally available in a pin DIL package. The two halves of port C can be either used together datashret an additional 8-bit port, or they can be used as individual 4-bit ports. Since the two halves of port C are independent, they may be used such that one-half is initialized as an input port while the other half is 825 as an output port.

When we wish to use port A or port B for handshake strobed input or output operation, we initialise that port in mode 1 port A and port B can be initilalised to operate in different modes, i. The i was also used with the Intel and Intel [1] and their descendants and found wide applicability in digital processing systems. The ‘s outputs are latched to hold the last data written dahasheet them.

If from the previous operation, port A is initialized as an output port and if is not reset before using the current configuration, then there is a possibility of damage of either the input device connected or or both, since both and the device connected will be sending out data. Some of the pins of port C function as ppo lines.

  BS EN 1011-3 PDF

Microprocessor And Its Applications. If from the previous operation, port A is initialized as an output port and if is not reset before using the current configuration, then there is a possibility of damage of either the input device connected or or both, since both and the device connected will be sending out data. For example, if port B and upper port C have to be initialized as input ports and lower port C and port A as output ports all in mode Acknowledgement and handshaking signals are provided to maintain proper data flow and synchronisation between the data transmitter and receiver.

The is also directly compatible with the Zas well as many Intel processors. Intel Intel D As an example, consider an input device connected to at port A. Only port A can be initialized in this mode.

So, without latching, the outputs would become invalid as soon as the write cycle finishes. Retrieved from ” https: It is an active-low signal, i. For port B in this mode irrespective of whether is acting as an input port or output portPC0, PC1 and PC2 pins function as handshake lines. This means that data can be input or output on the same eight lines PA0 – PA7.

Programmable Peripheral Interface – Intel Chipset Datasheet

The two halves of port C can be either used together as an additional 8-bit port, or they can be used as individual 4-bit ports. In this mode, the may be used to extend the system bus to a slave microprocessor or to transfer data bytes to and from datasheft floppy disk controller. By using this site, you agree to the Terms of Use and Privacy Policy.

It is an active-low signal, i. The functionality of the is now mostly embedded in larger VLSI processing chips pi a sub-function.

  M4A79XTD EVO MANUAL PDF

This is required because the data only stays on the bus for one cycle. Input and Output data are latched. When we wish to use port A or port B for handshake strobed input or output operation, we initialise that port in mode 1 port A and port B can be initilalised to operate in different modes, i.

This mode is selected when D 7 bit of the Control Word Register is 1. The control signal chip select CS pin 6 is used to enable the chip. Retrieved 3 June As an example, if it is needed that PC 5 be set, then in the control word. It was later cloned by other manufacturers.

For example, if port B and upper port C have to be initialized as input ports and lower port C and port A as output ports all in mode In this mode, the may be used to extend the system bus to a slave microprocessor or to transfer data bytes to and from a floppy disk controller. Only port A can be initialized in this mode.

Address lines A 1 and A 0 allow to access a data register for each port or a control register, as listed below:. Address lines A 1 and A 0 allow to access a data register for each port or a control register, as listed ppk.

Peripheral Parallel Interface for Parallel Port

Acknowledgement and handshaking signals are provided to maintain proper data flow and synchronisation between the data transmitter and receiver. Port A can be used for bidirectional handshake data transfer. Since the two halves of port C are independent, they may be used such that one-half is initialized as an input port while the other half is initialized as an output port.