ORG. GND. 8-lead SOIC. 8-lead dBGA2. 8-lead PDIP. 8-lead SOIC. Rotated (R). ( 1K JEDEC Only). 8-lead mini-MAP (MLP 2×3). 8-lead TSSOP. DO. DI. NC. VCC. CS. SK. 1. 2. 3. 4. 8. 7. 6. 5. GND. Normal. Pinout. Rotated. Pinout .. 93C Address bits pattern -> User defined. Timing Diagrams. Address. 8-lead SOIC. 8-lead dBGA2. 8-lead PDIP. 8-lead SOIC. Rotated (R). (1K JEDEC Only). 8-lead Ultra Thin mini-MAP (MLP 2×3). 8-lead TSSOP.
|Published (Last):||18 August 2015|
|PDF File Size:||10.45 Mb|
|ePub File Size:||17.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
I do not use it very often, now and every time I do I have to remove the token and then re-install the software. PIKprog2 discontinued Direct connection. The names of the chips in our database contain all characters necessary for identification rotste the device, but don’t contain such codes, that have no influence to the programming, for example temperature codespeed codepacking type codeetc.
My CDH Electronics gear has thrown it’s rotwte out of the pram again, and has to go back to see Colin, so I’m trying to read it with an Asix Presto, I wired it up as 93v46 rotated 93c46 and was unable to read, so tried as a normal one still the same. MEMprogL discontinued Direct connection.
BeeHive8S discontinued Direct connection. MEMprog discontinued Direct connection.
Thanks for the info on the 93c Blank A B C. Thanks MH, I think I will have to do that, sorry about your programmer, if it’s the one I think it is, there is only a handful of components on the board, cant you find out what’s faulty, or are you getting them replaced under warranty? Last time I tried it would not re-install, and so I am sending 93×46 back for later software to be added.
This rotte indicates quantity of items that could be produced from components in stock. If such code letter is at the end of the name, it should be omitted.
Maybe it is rotated, did you check on what pin is gnd? Any help would be appreciated. It was rotated, refitted it and radio now says error 3, so I think I have buggered it one way or the other, Still works if you hold down the band button and turn it on but it beeps all the time. They are going up as well if you look at later listings by the same seller they are more expensive. Read with a LV48 programmer. Device Search tip The names of the programmable devices in our database don’t contain all charactersshown at the top of the chip or mentioned 9c46 a datasheet section part 933c46.
Would I have damaged it if it was not rotated, and I read it as rotated. Move the cursor over the roate to highlight particular section. Pomona Electronics – http: If gnd on radio is on pin5 on pcb, so chip is normal, if gnd is on pin7 on pcb, so chip is rotated.
Ezoflash – Willem forum. Board: Chip issues. Topic: problem read 93c46 eprom
Reasonable quantity of this product can be available within 3 working days. In case of missed samples, we always asking the semiconductor manufacturer for samples, but if samples are not available – also in the package you’re asking for the support – the solution from us will be delayed. The sample of programmable devices is necessary to have for test and release new chip support.
Before years i tryed to read one rotated chip as rorate, more than times and ofcourse i did’n read it, then i ask a friend and he say that maybe it is rotated and i tryed it like rotated and read it sucsessfull, so there was not problem. Yes I have had CDH gear for about 15 yearsthe first interface i had had a sine wave generator for doing the early Philips radio’s with ER The real chips are also necessary to have in the case of reproducing issues from the created support.
Therefore we can return your samples only if we get chips from semiconductor manufacturer.