In the delivery of the card a pair of disc rollers scan the cross-section of the carded sliver as it emerges. These readings are compared electronically with the . Need of Autoleveller in. carding machine •Careful control of sliver uniformity is necessary in the spinning process. •So, continuous checking of sliver weight. Keywords: Autoleveller, Cotton yarn, Count variation, Draw frame. 1 Introduction able yarn count CV has been assessed for carded counts. The effect of single.
|Published (Last):||7 March 2016|
|PDF File Size:||13.37 Mb|
|ePub File Size:||19.57 Mb|
|Price:||Free* [*Free Regsitration Required]|
Finally, the drive to the delivery can present problems, since in this system the delivery speed must be continually varied, and in very small ranges.
Comparision between mixing and blending in Blowroo Most of the drawframe autolevellers are open loop autolevellers. The optical feeler is so arranged that the running sliver interrupts the beam of light and if the ahtoleveller breaks.
Auto Leveling in Carding | Part 04
Proper selection and positioning of machines in bl Prom this measured value a set point speed is derived for the variable speed motor which drive the draft roll. The sliver delivered from the calender roller passes beneath a guide located at the end of a lever.
This is the most commonly used principle of card auto leveling and serves to keep the sliver count constant. Auto Leveling in Carding: In the delivery of the card a pair of disc rollers scans the cross-section of the carded sliver as it emerges. Degumming of Silk March 14, Md. For various reasons, the card cannot always operate absolutely evenly, for example, owing to uneven material feed. During the entry of abonormal thickness of lap or metal pieces autoleveloer the feed roll, the knob raises.
Auto leveler (autoleveller) in carding | How it works?
To stop the doffer when sliver is missing or sliver is too thin or too thick or when the lap-up choking on coiler calender Roller. Graf ‘Optima” card auto leveller: In former Zellweger equipment a medium-term auto leveler was provided as an addition to the long-term auto leveler. Sliver break stop motion: Newer Post Older Post Home. An optical measuring device detects relative variations in the cross-section of the fiber layer on the autoleveloer cylinder over the whole width of the cylinder.
Spinning mills are therefore forced to use auto leveling equipment under highly varying circumstances. A limit switch is provided to prevent the starting of doffer when the coiler hood is opened. On the other hand, closed-loop control is not suited for regulating short-wave variation because of the dead time inherent in the system.
But the modern carding machines have sensing at the feed rollers as well as at the delivery calender rollers. Dust extraction systems in Carding Developments in licker-in section of Carding Machi Sliver variation cause the tongue upper roll to rise or fall. If caarding measuring point is located downstream from the drafting arrangement, or if the delivery roller pair itself provides the measuring point, then the system is operating on the closed-loop control principle.
Optical feeler in the coiler unit: Omar Faruk see all.
Autoleveller in Carding | Autoleveller in Drawframe – Textile Centre
Developments in carding section Auto leveler autoleveller in carding How it wo Grinding Roller For Carding machine How it works Settings in carding for autolevelller grades of cotton If the actual speed differs from the set point, the variable speed motor is de-accelerated or accelerated untill the two speeds coinside i.
Study of different parts of carding machine and th Peed Roller Stop Autolevelleer. In case of open loop system, as the delivered material is not sensed for its linear density to know whether the correction has made or not.
Long-term auto leveling is an integral part of modern cards, and in any case used in production of carded yarns and in the rotor spinning mill. How Laps formed in Blowroom? There are following advantages offered by an autoleveller system: The pulses derived in this way are processed electronically so that the speed of the in feed roller can be adapted to the delivered sliver weight via mechanical or electronic regulating devices.