This revision permits the publication of BS EN to be adopted as a Harmonised Standard under the Constuction Products Directive. BS EN. Hot finished structural hollow sections of non-alloy and fine grain steels -. Part 1: Technical delivery conditions d Copy. Find the most up-to-date version of BS EN at Engineering

Author: Datilar Volrajas
Country: Mayotte
Language: English (Spanish)
Genre: Life
Published (Last): 5 February 2018
Pages: 232
PDF File Size: 2.66 Mb
ePub File Size: 8.52 Mb
ISBN: 359-9-37887-124-2
Downloads: 6876
Price: Free* [*Free Regsitration Required]
Uploader: Taugal

NOTE Cold formed hollow sections with subsequent heat treatment to obtain properties equivalent to those obtained by normalizing rolling are deemed to meet the requirements of this standard.

Technical delivery requirements Status: Requirements for tolerances, dimensions and sectional properties are contained in EN Free to use BIM project management tool provides step-by-step help to define, manage and validate responsibility for information development and delivery at each stage of the asset life cycle in level 2 BIM projects.

Tables are in Annexes A and B, formula for calculation is specified. Ns lists and bibliographical references bz such national standards may be obtained on application to the Central Secretariat or to any CEN member. Please download Chrome or Firefox or view our browser tips. The scope of this annex is defined by Table ZA. The NPD option may not be used, however, where the characteristic is subject to a threshold level.

Where this document is specified, the purchaser shall notify the manufacturer of the address of the organization or person nominated by him to carry out the inspection and validate the inspection document.

This record shall be sufficiently detailed and accurate to demonstrate that all stages of the design phase, and all checks, have been carried out satisfactorily. For fine grain structural steel 01210-1 sections manufactured by either a seamless or welded process, repair of the body by welding shall not be permitted unless otherwise agreed. The minimum average values given in Table A.

The requirement on a certain characteristic is not applicable in those Member States MSs where there are no regulatory requirements on that characteristic for the intended use of the product. The N-binding elements shall be recorded in the Inspection Document. Method of test at ambient temperature EN The decision shall be left to the discretion of the manufacturer, but shall be stated to the purchaser at the time of enquiry and order.

  ARISTOTLE AND AARDVARK GO TO WASHINGTON PDF

The following samples shall be taken from one sample product of each test unit: For thicknesses less than 3 mm, the percentage elongation may be reported for a gauge length of 80 mm or 50 mm see 8. Table 4 — Test units Licensed Copy: Conditions techniques de livraison.

This applies in particular to personnel that needs to initiate actions preventing product non-conformities from occurring, actions in case of non-conformities and to identify and register product conformity problems. Otherwise, the NPD option may be used when and where the characteristic, for a given intended use, is not subject to regulatory requirements in the Member State of destination. For dated references, only the edition cited applies.

BS EN for Hot Finished Structural Hollow Sections

Personnel performing work affecting product conformity shall be competent on the basis of appropriate education, training, skills and experience for which records shall be maintained. The standard to be applied is at the discretion of the manufacturer. The BSI copyright notice displayed in this document indicates when the document was last issued. Design of steel structures – Part It presents the UK view on standards in Europe and at the international level.

Warmgefertigte Hohlprofile fuer den Stahlbau aus unlegierten Baustaehlen und aus Feinkornbaustaehlen.

SJ2H structural hollow section according to EN – SSAB

The grades and mechanical properties of the finished hollow sections are compatible with those in EN and EN Annex ZA of this European Standard ;? A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.

  INTRODUCTION TO PHYSICAL METALLURGY BY SIDNEY H AVNER PDF

Copyright Copyright subsists in all BSI publications. For details of these and other benefits contact Membership Administration. The Red document status indicator indicates that the document is an old version The document has likely been withdrawn by the publisher, also the meta data presented here may be out of date as it is no longer being maintained wn the editorial teams at NBS.

Identification number of the notified body;? The declaration shall be accompanied by a factory production control system certificate, drawn up by a notified body, which shall contain in addition to the information above, the following? BS EN EN and EN 6. Those relevant to this part are listed 10120-1 with appropriate clause references.

If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. A test unit is defined as 1021-01 quantity of hollow sections from one or more cast s of the same grade and dimensions, manufactured by the same process i. In these cases, verification of the grain size is not required. The requirements for tolerances, dimensions and sectional properties are contained in BS EN Users of British Standards should make sure that they possess the latest amendments or editions.

The results of inspections, tests or assessments requiring action shall be recorded, as shall any corrective action taken. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations.

BS EN 10210-1:2006

You hs find similar items within these categories by selecting from the choices below:. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies.

The faster, easier way to work with standards. Again there may be more recent versions of the document.