FTA Satellite Source offers the best in Free to Air Support for your Coolsat Pro FTA Receiver. File downloads, keys, firmware, tutorials, nagra2 bins, etc are . SERVICE MANUAL. TROUBLE SHOOTING. Coolsat. 6. 3. TROUBLE SHOOTING . Exterior Test. Check the condition of install, joining of connectors, broken. Coolsat // Manual Coolsat Guides & Discussions.

Author: Tulmaran Tuktilar
Country: Albania
Language: English (Spanish)
Genre: Sex
Published (Last): 3 April 2010
Pages: 444
PDF File Size: 5.50 Mb
ePub File Size: 19.62 Mb
ISBN: 492-4-50760-873-9
Downloads: 97656
Price: Free* [*Free Regsitration Required]
Uploader: Gular

These units have manuap been forgotten. Enter with remote as if choosing channel to open the CAS Menu or key edit function. Turn on power to the receiver with the rear reset switch on back of unit.

They tried again and the same thing happened. A prior work around has always been to delete transponder 1 off any custom channel list or to set your antenna settings as you think it should be and then enter the Motorized Dish setting in Installation and scroll ocolsat Echo 7 satellite and then scroll down to transponder and scroll up through transponders to verify signal for Echo 7.

Coolsat // Manual – FTA Bin Files Servers LinkBox Pinwheel DreamLink Jynxbox IPTV

To determine converted frequency, subtract the horizontal frequency number from 25, Satellite Base Address to obtain the new converted frequency number.

After setting the antenna settings you can now return coolsag loading the channel list if your prefer to load a custom channel list. Use of this feature enables your channels to match Dishnet channel order and Bev channel order beginning at Use the Lyngsat chart foolsat Only one cable out to receiver is needed and settings in the antenna are the same as Legacy settings except must be committed to lnb 1 and must be committed to lnb 2 and Lnb Type is set to OSC-DP.

After clicking on Normal Channels, find and browse in the.

In the present configuration for N2, we now see key lines 10 and 11 holding the 32 byte idea manial key and key lines 20 and 21 holding the 32 byte Idea key 1. N1 keys were comprised of 16 bytes containing the entire key string with N1 using an active key and inactive key held in the 00 and 01 key lines and these keys would alternate or roll to allow decryption.

  FR107 DIODE DATASHEET PDF

The DP34 can be used in place of a 4×1 diseqc or the 4×1 in place of the DP34 switch with limitations already noted. The and bin releases run in the same release version number format with the version of the receiver the file is for incorporated within the file name.

The following are some illustrations of what you will see when you enter the CAS or key edit function for N2 key edits.

Coolsat 4000 software, fta pay receiver tv

Key Tab 3 is for Dish Network N1 keys and key lines will show 00 4000 Since the release of the first modified bins, we have seen tremendous progress made in making the EPG for Coolsats better.

Be sure to turn the Sid Sort option off if you choose to use a custom channel list. The following are some illustrations of the scan modes. Click on Exit doolsat exit the Auto Detect.

Coollsat, unused Satellites now may be deleted, if you wish. A loaded channel 4000 will revert to custom channel list order when the feature is kanual off. This whole process takes under 10 seconds once your blind-scan is saved to your computer. When asked for password, enter Turn receiver on via the remote or front button. Some people had really been thrown for a loop when setting up their antenna for Echo 7 and finding no signal due to TP 1 being the default transponder on each satellite in Dish Setup to check signal.

Since release of the original Super Bin, a working auto roll is now fact for Dish and Bev. If you want to do it manually go to www. As you scroll through the transponders on the list you will see each transponder listed by frequency, Symbol Rate and Polarity. Attached is a conversion chart from Legacy to Dishpro forand satellites at the end of this manual. I think this is what you’re looking for Repeat the coolsay by going to the next coolsa you want to add by clicking on the green button, and continue for all transponders you wish to add until you have finished.

  ANSELL 11-627 PDF

Tuning to this channel for a few manusl will also enable the EPG list to populate faster. Then select the type of conversion. I have found the easiest way to edit keys is to use the Ok button to open the Key Pad and use it for entering alpha characters and to enter numerical entries with the remote channel number entries.

Linkbox Files Only! To do this- simply right-click any channel and select “Fill missing Channels”. New Channels locals or otherwise can be inserted manually. Do a factory reset: The tool will say 2.

Coolsat Pro FTA Support

Your channel file will have a. Unzip the tool and place it in a handy place on your personal computer so you can locate it easily. Do not interrupt until the Finish window opens.

Most satellites use a base address of but some satellites use a different base address. The Coolsat has 8 categories or groups for saving favorite channels.

Treat the DP34 the same as an external diseqc switch and run a cable from each lnb as set out above for making cable connections when using more than two lnbs. Wait until download in complete