The 2N, 2N, 2N and 2N are sili- con planar TO (for 2N and 2N) and in Jedec . This datasheet has been download from. Semelab encourages customers to verify that datasheets are current before Test Conditions. Min. Typ. Max. Unit. LAB. SEME. 2N IC = 10mA. IB = 0. Sep 2. Philips Semiconductors. Product specification. NPN switching transistors. 2N; 2NA. FEATURES. • High current (max.
_0001.jpg "datasheet 2n2219")
| Author: | Madal Yozshubar |
| Country: | Thailand |
| Language: | English (Spanish) |
| Genre: | Sex |
| Published (Last): | 27 April 2017 |
| Pages: | 334 |
| PDF File Size: | 6.87 Mb |
| ePub File Size: | 19.61 Mb |
| ISBN: | 745-7-67931-529-3 |
| Downloads: | 35205 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Malazuru |
Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below. Where h FE, is the current gain of the transistor ratasheet in our case is The 2N is a NPN transistor and is normally used as a switch in many circuits.
Here lets us assume the load here consumes around mA maximum so our collector current I C mA. Submitted by admin on 21 June dataasheet This resistor is connected to the base pin of the transistor to limit the current flowing through the base. Current flows in through collector, normally connected to load. Amplifier modules like Audio amplifiers, signal Amplifier etc. Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which datssheet our case according to the data sheet 1.
2N Datasheet, Equivalent, Cross Reference Search. Transistor Catalog
Current Drains out through emitter, normally connected to ground. But this calculation will lead to the closest value to start with. As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on.
However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor.
TL — Programmable Reference Voltage. Another important thing to keep in mind, while using a transistor as switch is the base resistor. The maximum amount of current that could flow through the Collector pin is mA, hence 2m2219 cannot connect loads that consume more than mA using this transistor. In our case for a collector current of mA we have to pass a base current of 16mA.
The value of this current can be calculated by the required amount of current that 2j2219 be consumed by the load. So the value if R B will be. To make this current flow through the transistor the value of base current I B can be calculated using the below formula: When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.
Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits.
2N2219 Datasheet, Equivalent, Cross Reference Search
To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the datashet pin.
When this transistor is fully biased datadheet it can allow a maximum of mA to flow across the collector and emitter. So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project.
To make this current flow through the transistor the value of base current I B can be calculated using the below formula:. So to calculate the resistor value of the base we can use the formulae.
Complete Technical Details can be found at the datasheet given at the end of this page. But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle.
This stage is called Saturation Region.