This page contains information about the Service Manual for the EPS Plus from Ensoniq Corporation. Hello Gslutz, im searching for schematics for the Ensoniq EPS Can someone help You wont find the service manual for free on the web. 21 EPS—16 PLUS Service Manual Table of Contents — 1 Table of Contents . For more information about the Poly-Key Keyboard assembly, see ENSONIQ.
| Author: | Mazulkree Nakree |
| Country: | Albania |
| Language: | English (Spanish) |
| Genre: | Music |
| Published (Last): | 8 October 2004 |
| Pages: | 265 |
| PDF File Size: | 10.17 Mb |
| ePub File Size: | 1.36 Mb |
| ISBN: | 920-1-48637-666-9 |
| Downloads: | 87056 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Kazrashicage |
Be sure to use machine screws in these locations. The board has all of the connectors except the disk drive connector, J2 in a different place from the board.
Install the five 5 self-tapping screws on the back of the unit. A file name should appear in the display.
Ensoniq EPS 16+ Service Manual
Carefully reconnect the four cables, paying particular attention to the alignment of pins and connectors. The Disk Drive test is run approximately every ten minutes and takes about five minutes to run.
Install die two 2 self tapping screws on either side of the unit 3. Section 8 – Sequencer Basics Disconnect the transformer cables to the servixe supply, line filter, and power switch.
ENSONIQ EPS 16 Plus Service Manual
For best results, make sure your area is well lit. Remove the one 1 machine screw from the top of the unit located about 1″ back from the control panel this screw goes through the disk drive mounting bracket inside the unit.
Immediately place ensonis defective drive into the anti-static bag that the new drive came in. Remove the four 4 screws that attach the Disk Drive mounting brackets to the control panel.
Full text of “Ensoniq EPS 16+ Service Manual”
Create a short sequence by pressing Record and Play at the same time Use the sustain right pedal to verify that sustain works, then stop the sequencer using the sequencer left pedal Press Cancel-No If one or both of the footswitches do not operate properly, make sure that the footswitches are set to the proper mode as outlined on page 50 of the EPS Musician’s Manual The above test assumes that the left pedal is set for sequencer control and the right pedal is set for sustain this is the default.
Install the four 4 self-tapping screws on the bottom of the unit closest to the control panel. You may need to add a small amount of solder to each hole so the braid will have contact with and absorb any remaining solder. Remove the Volume and the Data Entry knobs.
We suggest removing all cable connectors using the angled end of a scribe see below. It is important, therefore, to transfer the metal plate from the old drive to the replacement drive.
Removable SCSI drives are no longer surveyed like the internal floppy drive for disk cartridge being changed.
Hall Reverb, 44khz Reverb, Room Reverb Remove the four ensonis screws that fasten the control panel with a 2. Install the new KPC simulator board onto the standoffs making sure the side of the board with the pin connector is closest to the base of the unit.
Verify that no pressure effect occurs. Re-saving a SYSEX file now uses the correct file name; previously, the file was saved using the name of the last-saved file. Make Loop Longer Visit us on the web at: Note that there are star washers on the servkce sides.
ENSONIQ EPS SERVICE MANUAL Pdf Download.
Midi System Exclusive Recorder The module ears were not designed to fit into the recessed area. What disks to use It is very important to use double-sided, double-density 3. The ripple must be less than 50mv. Insert the new Transformer and attach it to the base using the four screws and flat washers.
Connect the two cables, paying particular attention to the alignment of pins and connectors.
With the board tilted on a slight angle, insert the jacks into the holes in the rear panel Press the board down and into place. Remove the four 4 self-tapping screws from the top of the unit closest to the control panel. Performance Tip – Creating Keyboard Splits