FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Zologore Shakakora
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Spiritual
Published (Last): 21 July 2015
Pages: 432
PDF File Size: 15.36 Mb
ePub File Size: 18.46 Mb
ISBN: 731-4-68411-228-6
Downloads: 5675
Price: Free* [*Free Regsitration Required]
Uploader: Mutilar

Release the mechanical brake. When the replacement is necessary, contact your Fuji Electric representative. No part of this publication may be reproduced or copied without prior written permission from Fuji Electric Co.

When the dielectric strength test is necessary, contact your Fuji Electric representative. Note 2 To protect wiring, insert a molded case circuit breaker MCCB or an earth leakage circuit breaker ELCB with overcurrent protection of the type recommended for the inverter between the commercial power ,ift and the inverter.

A box in the above figure replaces C, E, A or J depending on the shipping destination.

For the motor, check the rated values printed on the nameplate of the motor. Page Fuji Electric Co.

Immediately trip with alarm processing 1: To use it follow the steps listed below. Install FRENIC-Lift in compliance with the local regulations, Described below for frfnic example, a procedure shows an installation of the inverter in compliance with regulations in Japan. Page 60 y codes: You need to replace the option card. Torque bias gain adjustment BTBG.

  CULTURAL STUDIES TEORI DAN PRAKTEK CHRIS BARKER PDF

Page 59 H codes: For the braking resistor built-in type, refer to the next page. You may drop the inverter or break it. Please do not use it with frenif products. Page 24 – Terminal arrangement and screw specifica These are provided for the DC link bus powered system.

Fuji Electric FRENIC-Lift series Instruction Manual

Page 49 An undervoltage or an alarm has been occurred. Terminal Arrangement And Screw Specifications 2. Measure the output current. Page 35 Table 2. Page 29 Follow the procedure below for wiring and configuration of the inverter.

Possible Causes What maual Check and Suggested Measures 1 No power supplied to the Check the input voltage, output voltage and interphase voltage unbalance.

Wiring For Rfenic Circuit Terminals 2. Page 9 Select an inverter according to the applicable motor ratings listed in the standard specifications table for the inverter. Page 54 F codes: In the following description, the inverter has already been installed.

FRENIC-Lift | Fuji Electric Global

When employing external cooling At the shipment time, the inverter is set up for mount inside your equipment or enclosure so that cooling is done all internally. Refer to Figure 2.

Brake control by output current Operation level 0 to ON delay time 0. Attachment for This adapter allows you to mount your FRENIC-Lift series of inverters on the panel in such a external cooling way that the heat sink ftenic may be exposed to the outside.

Each function code consists of a 3-letter string. Apply motor the inverter after consulting llift motor maker. Consult your Fuji Electric representative if these terminals are to be used. Consult your Fuji Electric representative.

  ANTHONY ALAYON PDF

FUJI ELECTRIC FRENIC-LIFT SERIES INSTRUCTION MANUAL Pdf Download.

For details, refer to [X2] Digital Chapter 5, Section 5. Page of Go.

Disable Times Times 1 to Do fenic hold covers or individual parts only. Don’t show me this message again. Page 77 [ 16 ] Run operation error Problem You incorrectly operated the inverter.

List Of Periodical Replacement Parts Each part of the product has its own service life that will vary according to the environmental and operating conditions. In this case, take countermeasures such as installing the inverter in a place that easily protects human body from electric shock. Brake control by time 2: FRENIC-Lift is an inverter designed to drive a frejic induction motor hereafter called an induction motor and a three-phase permanent magnet synchronous motor hereafter called a synchronous motor for exclusively controlling elevating machinery.

Recommended Wire Sizes 2. Enable data prot ection Note: Page 40 Table 2. Page 38 Table 2. Page Name of option Function and application Insert an MC in the power source side of the inverter in order to: When the inverter is used to run manusl general-purpose motor, the temperature Torque characte- of the motor becomes higher than when liift is operated using a commercial ristics and tem