HTX Datasheet PDF Download – LCD Module, HTX data sheet. BOEHYDIS HTX LCD Screen ” XGA For Lenovo X60 X61 42T 42T | Computers/Tablets & Networking, Computer Components & Parts. Find great deals for IBM ThinkPad X61 LCD Screen Htx 42t Shop with confidence on eBay!.

Author: Tauramar Kigale
Country: Bhutan
Language: English (Spanish)
Genre: Finance
Published (Last): 11 February 2015
Pages: 248
PDF File Size: 1.28 Mb
ePub File Size: 3.43 Mb
ISBN: 608-1-84665-322-5
Downloads: 24920
Price: Free* [*Free Regsitration Required]
Uploader: Shaktizilkree

Know more about this protection. When sliding the LED strip into place, the fit should ut121x01 just a bit snug. The shipping might take more than 14 dayswith tracking number. It’s best to be conservative, remove small slivers, check the fit one bead at a time, adjust, repeat. The prep process is the same regardless the specific model number. Seller information sci-electronics This tape covers three short, flexible ribbon cable tabs extending from the side of the glass LCD layer.

When the bracket yt121x01 not grounded, the LED strip can only short to itself, which is relatively harmless due to current limiting. Do not leave the machine powered if there is any problem with operation of the backlight. On non-tablet screens, pay special attention to the edges around the front of the 11.

Panel after tape and screw removal.

IBM ThinkPad X61 LCD Screen Htx 42t | eBay

The screen bezel is held in place both with screws and small plastic th121x01 along all four sides of the screen; some of the latches pop apart hh121x01, but most pop apart sidewaysoften alternating inward and outward. The lower mounting tabs on the tablet AFFS screens will partially obstruct access to the backlight channel in later steps. If you have one of these screens and it does not show a pattern, you’re a lucky bastard and I want to know more about it: The side-mounting clips both provide the mounting threads for the hinges and connect the backlight bracket to ht12x01.

For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fees.

Brand New Grade A+ laptop lcd screen HT121X01-101 work for IBM ThinkPad X60 X60s X61 X200

We cut the connection to the backlight bracket off each clip, and will replace the clips back onto the mounting tabs later during final reassembly. Shims can still be added behind the LED strip to adjust the size of the gap.


Slide a thin 10mil. The easiest way to remove the original CCFL is to snip the wires free at both ends of the tube, trim away the thin plastic tabs holding the backlight tube in place at both ends, and then carefully pull the CCFL tube out of the ht1221x01.

If any of those connections pulls free, it’s Game Over: If this screen is a finger-touch model what Lenovo used to call ‘multitouch’ before that term came to be used for multiple-finger touch sensingdisconnect the ribbon cable stretching from the front of the panel around the side to the Wacom digitizer on the back. The machine screws holding the LCD panel controller to the frame are circled in red.

Removing the CCFL tube does not require complete panel disassembly, but it does require popping the panel frame slightly open. Consult the image below for correct orientation. Remove the white and the yellow pieces of polyester tape along the bottom and sides of the panel that secure the frame, backlight bracket, and rear reflector surface to one another.

This is where the accordian strip comes in. This item will ship to United Statesbut the seller has not specified shipping options. It’s possible to connect X60 and X61 tablet inverters to the LCD cable backward; doing so will blow fuse F2 on the motherboard.

Make sure all hasps along the bottom and both sides are mated. Placed in front of the LED strip, it adds an air gap by holding the LED strip away from the waveguide, but also holds the LED strip firmly in place against the backlight bracket.

If an LED driver board that is trimmed for a specific ThinkPad model is plugged into a different model, it’s expected that the brightness range may not be entirely correct.

New other see details: This item will be shipped through the Global Shipping Program and includes international tracking.

(PDF) HT121X01-101 Datasheet download

The inverter is shown in mounting position. If the fit is loose, repeat the process adding another shim behind the strip. Leave the flexible tabs along the right side of the panel exposed for now; be careful not to abuse them by tugging, yanking, or shocking them flexing is fine, just touching them also won’t break anything.


Return the black screws that secure the sides of the metal front frame to the internal plastic frame. The TN panels have square-shaped backlight channels. Do not replace the black screws we removed from the sides of the frame, as we still need to pop the metal frame open later. This is also the only good option for holding side-emitting LED strips in the proper slightly down-rotated position.

Bonding the LEDs with tape is also a complex task that requires completely disassembling the panel to extract the backlight bracket, and then once the LED strip is installed, it can’t be removed. Please provide feedback after you receive your order. The touch sensitive front layer is connected to the Wacom controller via the ribbon cable circled in red. A few kits e. Unscrew the two black machine screws on the sides of the screen near the bottom that attach the metal outer frame to the inner plastic frame.

Image not available Photos not available for this variation. Personally, I prefer to remove the clips, make a clean cut cut, and replace.

Knead each bead to wrap around the top and bottom being careful not to obscure the LED emitters. Do you have laptop spare parts or electronic components which will be of interest to Customers of PcHub. We only need to fill mils of space, and small plastic sheets with tight thickness tolerances are readily available from hobby supply stores in.

Remove the metal clips ht121x10 the sides of the panel that cover the plastic mounting tabs and are secured to the white plastic frame with tiny screws.

In this picture, the tape along the bottom of the panel hasn’t yet been replaced.