IEC Standard | Switches for appliances – Part Requirements for mechanical switches. This part of IEC applies to switches for appliances. The switches are intended to control electrical appliances and other equipment for. This part of IEC applies to electronic switching devices and shall be used in conjunction with the general requirements of IEC

Author: Vudosar Kek
Country: Guinea
Language: English (Spanish)
Genre: Photos
Published (Last): 14 September 2009
Pages: 215
PDF File Size: 20.16 Mb
ePub File Size: 8.20 Mb
ISBN: 194-1-61620-803-6
Downloads: 75114
Price: Free* [*Free Regsitration Required]
Uploader: Nezshura

Characteristic Subclause fjleatis of information Common type reference C.

Switches for appliances – Part 1: General requirements

The symbol for the nature of the supply 610581- placed after the current and voltage ratings. Clearance is the shortest direct air path over the top of the barrier.

This standard is also available to be included in Standards Subscriptions. Examples of screwless terminals are 6108-1 in figure 6 3. Care shall be taken that the results from one series of three blows do not influence subsequent series.

In cases wfiere basic insulation and supplementary insulation cannot be tested eic, the insulation provided is subjected to the test voltages specified or reinforced Insulation. If a decorative cover is backed by an inner cover, fracture of the decorative cover is neglected if the inner cover withstands the test after removal of the decorative cover After both of these tests, the specimen shall show no damage to impair compliance with this standard If a switch is intended to have an actuating member but is submitted for approval without, then a pull and a push of 30 N are applied to the actuating means.

If there are more than one ON positions, then the verification shall be realized at the most unfavourable one If he switch has a mechanical 16058-1 which is connected m parallel to the semiconductor switching device, he temperature is 61508-1 in the position immediately before the contact closes.

Compliance is checfied during the tests of clauses 14, No significant displacement or damage shall occur. During and after the test, the specimens shall operate correctly.

  JAPO BAYERN PDF

Full text of “IS/IEC Switches for appliances, Part 1: General requirements”

The test circuit is shown in figure Compliance is checked by the dust test according to lEC Eacli break snaii be not less than one-third of the prescribec distance Classes H to The diagram of the circuit in which the switch is tested Is shown in figure Compliance is checked by inspection. You may experience issues viewing this site in Internet Explorer 9, 10 or Fixing screws for ief are tightened with a torque as specified in table Particular requirements for cord switches Switches for appliances — Part They shall 61085-1 constructed so that if any conductive part of the switch becomes loose and moves out of position, it cannot get so disposed in normal use that creepage distances or clearances across supplementary insulation or reinforced insulation are reduced Compliance is checked by inspection, by measurement and by 6158-1 test For the purpose of this 61508-1 The conventional fusing currents to be used for these tests are specified in table 26, Table 26 – Conventional fusing current versus rated current Device Rated current A Conventional fusing currenl’l A Cord switches Up to and including 16 26 Indepondont’y mounted switches Up to and including 16 26 Lec 16 up to nnd inrliidmg 3?

Amazon Renewed Refurbished products with a warranty. Take the smart route to manage medical device compliance.

BS EN IEC 61058-1:2018

Each terminal shall be located near to its corresponding terminal of different polarity, and to the earthing terminal, if any, unless there is a sound technical reason for the contrary.

If a switch is delivered without an actuating member, then a suitable actuating member should be supplied by the manufacturer for the purpose of this test; f for accelerated speed: In this case, soiid insulation will not be subjected to the same withstand requirements as when testing at sea-level.

Compliance Is checked by inspection, by manual test and by the appropriate tests of clause 1 1. Standards Subsctiption may be the perfect solution. Test plans otiier tlian as described in this annex may be used if determined to satisfy the same purpose.

  COURAGE BY BIENVENIDO SANTOS PDF

Tests according to S.

IEC | IEC Webstore

During these tests, a movement of the actuating member iiec the actuating means is acceptable provided this does not result in an incorrect indication of ie switch position. Disclosure to Promote the Right To Information Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public ied, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public.

Compliance with 6105-81 flammability criteria is checked according tb lEC Cable inlet openings, if any, and drain-holes are left open. Amazon Rapids Fun stories for kids on the go.

During the test, the maximum rated current is passed through the switches. Supplementary requirements for fuses for use by unskilled persons fuses mainly for household and similar applications — Sections I to IV Graphical symbols for use on equipment application Fire hazard testing uec Part NOTE For a specilic lamp load, it is recommended that he specimen be operated with loads that arc used in tHe field father than with synthetic ieec, Forced cooling of the specific lamp load may be applied in ordur to ensure cold resistance for each operating cycle and shorten the test time For electronic switches, the test circuit shall be as shown in figure 19 The declared load shal, be set at rated voltage before the electronic switch is inserted into the circuit