View and Download Lenze series operating instructions manual online. Inverter Drives Variant Dancer-position control with Torque control. series. vector. System/Component overview. Lenze. FU vector en 11/ 3. System overview/Selection guide. Communication modules e.g. keypad or. PROFIBUS. Get Lenze IB Manual. Get all Lenze manuals! with optical fibre cable together with the controller series as of E DC controller E 5x. 6x.
| Author: | Mazulmaran Majas |
| Country: | Latvia |
| Language: | English (Spanish) |
| Genre: | Career |
| Published (Last): | 3 March 2011 |
| Pages: | 417 |
| PDF File Size: | 8.29 Mb |
| ePub File Size: | 18.87 Mb |
| ISBN: | 543-3-81543-967-8 |
| Downloads: | 17584 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Kakinos |
In this state, a pulse inhibit is possible any time. Your manual failed to upload Automation status word 58C4hex Data format: Adapter Fis lecom Interface X6 Summary of Contents for Lenze series Page 2 These Operating Instructions are valid for the units with the following nameplate data: I Controller Enable Enabling with terminal Fuses 49 control 87 Miniature circuit breakers 49 Additional 86 Changing the functions of terminals 21, Accessories 22 61 Brake resistors Unsigned16 The parameter “automation status word” is used to show compact information about the drive system.
To ensure the data consistency of the process output data output data of the masterthe parameter “enable process output data” is necessary.
Lenze – : DACPOL-SERVICE
Process data description structure index 20hex. Integral Action Component Because of the generation of leakage currents, the RFI filters must be lezne to earth.
Page 28 Installation Connect the Controller, mains fitter, and mains Choke to the grounded mounting plate. 860 cyclic overload, the ratio overload to cycle time must not exceed 0. For this, the torque setpoint is entered via an analog Signal input which is permanently compared with the torque supplied to the motor shaft.
Setting Of The Pid Controller 9.
These JOG frequencies replace setpoint 1. These persons tan discharge themselves by touching the PE fixing screw manul another grounded metal part in the control cabinet. Loop control with Speed ada Minimum Field Frequency Fdmin Initiate The initiate service is used for the logic initiation between two participants.
Without automation module 1. It contains status information of the controller states and other important information. The controller receives new data from the master, lenzf it does not use them.
DP parameter setting channel 3. Settings for the master Most of the controller manufacturers demand a controller description file controller master data file.
LENZE SERIES OPERATING INSTRUCTIONS MANUAL Pdf Download.
FMS process data Process data are data memories where several individual parameters are combined to form a new parameter, the process data.
Speed quick stop Ahex 4. An acknowledgement or a fault indication are output. Programming The programming section using the IB bus interface module is divided into the following chapters: Description of the process data which the controller transmits to the master input data of the master. Operation at rated power factory setting 8 6 0 3 8 6 0 4 3 x 2.
What’s missing? Tell us about it.
Selection Of The Configuration Basic Parameter setting Programming of the frequency controller enables the drive to be adapted to your application. Cable protecting fuses for recommended – 03 Controller type Rated fuse current 2 0 A 3 5 A 5 0 A 16 mm2 Lneze Cross-sectlon 4 mm2 6 6 1 2 6 6 1 4 8 6 1 5 Controller type 6 3 A A The brake contact which is switched in the event of overtemperature is designed for: Therefore, the master can load process data in the controller and activate them simultaneously using a Sync command to one or several drives.
Name Parameter Facto- setting is printed in bold Preselection: In this configuration, only one motor tan be connected.