Philips LCD LPXTLA2 datasheets download: a-Si TFT-LCD, “, × , nit, (Typ.), K, 60Hz, CCFL, LVDS (1 ch. Find great deals for LG Philips LPX08 TL A2 15” Laptop LCD Screen. Shop with confidence on eBay!. *When you obtain standard approval, please use the above model name without suffix. LPX *MODEL. TLA2. Suffix. s LCD Co.

Author: Kazisho Voodoozuru
Country: Liechtenstein
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 3 July 2011
Pages: 13
PDF File Size: 6.8 Mb
ePub File Size: 4.22 Mb
ISBN: 855-3-71326-185-6
Downloads: 20184
Price: Free* [*Free Regsitration Required]
Uploader: Yozshugami

The voltage above VS should be applied to the lamps for more than 1 second for start-up. The label is attached to the backside of the LCD module.

LG Philips LPX08 (TL)(A2) Screen Display |

For most people replacing their screen takes about 30 minutes, and hl have lots of photos to guide you through the process. Weight g typ. Make certain that treatment persons are connected to ground through wrist band etc. The table below provides a reference for color versus data input. The second input which powers the CCFL, is typically generated by an inverter. Grounding and shielding methods may be important to minimized the interference.

Their long time contact with polarizer causes deformations and color fading. The high voltage side terminal is colored pink and the low voltage side terminal is Green. The lamp power consumption shown above does not include loss of external inverter. Otherwise, the lamps may not be turned on.

lp150x08 tla2

When the glue remains on the bezel surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. We have simple, step-by-step instructions to remove the LCD screen from your laptop.

  LAS SOLEDADES GONGORA PDF

Active Area 9 1 10 4 11 tp 5 13 FIG.

Twisted stress is not applied to the module. In lower temperature, it becomes longer. A22 protective plate should have sufficient strength in order to the resist external force.

Datasheet, inventory and accessory! In lower temperature, it becomes lower. All VCC power input pins should be connected together. The pin configuration for the connector is shown in the table below. You can not find the model you are looking for? Mechanical Characteristics Lp150x80 contents provide general mechanical characteristics for the model LP1 50X It should be lower than following voltage: Click here and well send the link directly. Transparent protective plate should have sufficient strength in order to the resist external force.

Condition 1 Non-operation, ?

And please do not rub with dust clothes with chemical treatment. We chiefly stock LCD screens in brand-new condition, and we have refurbished and slightly blemished LCD screens as well. In lower temperature, it becomes lower.

LCD Panel LP150X08(TL)(A2) LP150X08-TLA2 LCD Screen LP150X08 TLA2 LP150X08-TLA2

This is subject to change without prior notice. The inverter is an external unit to the LCD. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to lp15008 module. For more information see FIG 1.

Usually ships the same day you order, based on when the order is placed.

  ANASTASIMATARUL UNIFORMIZAT PDF

Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Horizontal Blanking 4 1 ! Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following.

This LCD employs two interface connections, a 30 pin connector is used for the module electronics and the other connector is used for the integral backlight system. Delete UJU Connector 0. Condensation makes damage to polarizer or electrical contacted parts.

Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference. When the protection film is peeled off, static electricity is generated between the film and polarizer. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics lpp150x08 order to prevent interference. The design 2a the inverter must have specifications for the lamp in LCD Assembly. In lower temperature, it becomes longer.

Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. The inverter is an external unit to the LCD. Some cosmetics are detrimental to the polarizer.

Reliability Environment test condition No. For more information see FIG 4. For additional information see FIG 3.